Midland BT Next 2.0 User Manual download pdf (Page 28)

Midland BT Next - 27

Back to factory setting

Sometimes you may nd it necessary to go back to the factory setting, to reset all

the changes/setup already made and have a “clean” unit.

To perform this operation you must rst enter the setup mode:

› Turn o the unit

› Press and hold down the “Middle” button about 7 sec., until the Red light is

on permanently.

› Than simultaneously press and hold down all the three buttons “Forward”-

“Middle”-“Rear” for 3 seconds. The Blue Light will be lit on for 1 sec and than

back to steady RED.

› Double click on the “Middle” button to exit the “Setup” mode and use the

BTNext.

Adjusting/ Disabling the VOX feature (Intercom and telephone)

The Intercom feature can be enabled both manually and vocally (VOX). The VOX

activation is inuenced by the helmet type, the background noise and therefore

by the speed.

For optimum results, it is possible to choose one of the following four microphone

sensitivity levels: high, medium, low and very low. The default setting of BTNext

is “low”. It is also possible to disable the VOX feature in order to activate the Inter-

com and phone call answering features in manual mode only.

Adjusting the sensitivity of the microphone (VOX)

To perform this operation you must rst enter the setup mode:

1. Turn o the unit

2. Press and hold down the “Middle” button about 7 sec., until the Red light is

on permanently.

3. Your BTNext is now in “Set up mode”.

4. Press the “Rear” button shortly and the red light changes to a steady blue.

5. Now, press “Volume +” or “Volume -“ to increase or reduce sensitivity. Every

time you press the Volume buttons the RED light will ash for conrmation.

When you reach the end of the upper and lower limit, the RED light will not

ash.

6. Press again the “Backward” button shortly; the Blue light will ash several

times, in order to let you know the selected sensitivity:

One ash = VOX disabled

Twice = very low sensitivity

3 times= low sensitivity

4 times= medium sensitivity (default setting)

5 times = high sensitivity

The light indicator is now back to steady RED (“Set up mode”) and the

changes are conrmed

7. If needed, you can adjust again the sensitivity repeating the steps from point

1, otherwise exit the Setting mode by double clicking the “Middle” button.

Once the red light turns o, the blue led starts blinking. Now you can use your

BTNext.

Disabling the VOX feature (Intercom and telephone)

Follow all the procedure described in the previous steps and choose the option of

only one ash (VOX disabled).

Attention! If you disable the VOX feature, you will be able to answer incoming phone

calls only by pressing the “Forward” button.

Wired connection always in background

This feature let you keep the wired connection always on, even when the phone

or the intercom is open. This feature can be useful when you connect a PMR446

transceiver.

By default this option is on.

Disabling:

› Enter the “Setup” mode:

› Turn o the unit

› Press and hold down the “Middle” button about 7 sec., until the Red light is

on permanently.

› Press the “Forward” and “Middle” button together for 3 seconds. The blue LED

will ash three times. twice.

› Double click on the “Middle” button to exit the “Setup” mode and use the

BTNext.

Enabling: Follow the same procedure up described; now the blue LED will ash

once. To exit the “Setup” mode, double click the “Middle” button.

Setup and Firmware update

It is possible to congure and update the rmware of your BTNext using the

USB connection to your PC. On the Midland web site www.midlandradio.eu in

the BTNext page you can nd the PC software and the new rmware updates

if available.

ATTENTION DO NOT CONNNECT THE UNIT TO THE PC BEFORE you DOWNLOAD AND

INSTALL THE SOFTWARE

1 2 ... 23 24 25 26 27 28 29 30 31 32 33 ... 135 136

Comments to this Manuals

No comments

Midland BT Next 2.0 User Manual Page 28

Comments to this Manuals

Related products and manuals for Communication Midland BT Next 2.0