Midland BT Next Conference Specifications download pdf (Page 30)

Midland BT Next - 29

Hint: We recommend that you perform a few tests adjusting the volume of your

iPod/MP3 player so at the normal speed the Headset volume is suited to your needs.

The AGC system will automatically increase the volume on higher speed. Make a

note to remember this setting for future trips.

Enabling/disabling the wired input

If needed the wired input can be enabled or disabled:

Enabling/Disabling: Make a Long press on the “Forward” and “Middle” button (you

will hear one audio beep tone for enabling conrmation and two audio beep tone for

disabling).

Priority

The BT Next C. manage the dierent connection/audio sources based on the following

priority rules.

Changing of the operative mode

Every time you change mode (long press of the middle button to toggle between In-

tercom/ FM Radio / Phone), the previous audio is closed and the control goes to the

new mode.

Intercom

The Intercom has always a higher priority against the music from the FM Radio or Pho-

ne (including GPS in music play mode). Every time you open the intercom the music

from a Bluetooth source is stopped. Only the audio/Music from the “AUX wired connec-

tion” is always in background by default.

Phone calls

The phone call has always the higher priority and will interrupt every connection, like

music, intercom. Only the AUX wired connection can be still on if the setting “Wired

connection always in background” was enabled.

GPS voice announcement

When the GPS is paired to the “Volume +” button,(high priority) the street voice an-

nouncement will always interrupt the intercom.

When paired using the “Volume -” button, (lower priority) the voice announcement are

always in background also if the intercom is active.

AUX wired connection

Music or audio from the AUX wired connection, by default it is always in the background

also when the intercom is open or during a phone call. It is possible to change this bea-

ver following the procedure described in the “Setup and Special conguration” chapter.

Using a PMR446 transceiver with the cable connection

In order to connect the transceiver to your Midland BT Next C., you need to pur-

chase the specic 2.5mm plug AUX cable, sold separately. Some manufacturers

radios use a dierent pin conguration, so we recommend that you ask your dea-

ler as to which cable is best suited to your needs

The cable connected to the transceiver normally has also a PTT button that can be

placed on the handlebar of your bike or held in your hand (If you are the pillion

rider). To communicate via the attached radio, press the PTT button to speak and

release it to listen. It is not possible to talk and listen simultaneously.

Adjust the volume of the transceiver to your needs, remembering that the volume

adjustment is controlled by the automatic AGC system and that it will therefore

be automatically increased in relation to background noise.

If you wish to use a PMR446 transceiver for group communications and simulta-

neously maintain the Intercom feature enabled between two or more BT Next C.

devices, you must remember that every time you talk to communicate with the

PMR 446 transceiver (pressing the PTT button), you will also activate the intercom

of the BT Next C. to the unit connected to the “Middle” button (thanks to the VOX

feature).

To avoid the Intercom activation when you speak on the PMR446, you can decide

to pair the BT Next C. unit on the “Rear” or “Forward” (where the VOX is not active)

or if you still want to use the “Middle” button, you must disable the VOX feature,

as explained in the previous section.

Setup and special conﬁgurations

Resetting all paired devices

Sometimes you may nd it necessary to delete all the pairing references stored in

the BT Next C. unit (reset operation).

To perform this operation you must rst enter the setup mode:

› Turn o the unit

› Press and hold down the “Middle” button about 7 sec., until the Red light is

on permanently.

› Then simultaneously press and hold down the “Volume +” and “Volume –“

buttons for 3 seconds. The Blue Light will be lit on for 1 sec and than back

to steady RED.

› Double click on the “Middle” button to exit the “Setup” mode and use the BT

Next C..

This procedure deletes all the paired Bluetooth devices stored in the memory and

it is therefore possible to start a new “clean” pairing session.

1 2 ... 25 26 27 28 29 30 31 32 33 34 35 ... 117 118

Comments to this Manuals

No comments

Midland BT Next Conference Specifications Page 30

Comments to this Manuals

Related products and manuals for Motorcycle intercoms Midland BT Next Conference