Midland BT NEXT User Manual download pdf (Page 6)

6 - Midland BT Next midlandusa.com

English

How to pair two BTNext units

The two units supplied in the same BTNext box, are already paired and ready to use,

which mean you don’t need to perform this procedure. The unit are already paired

using the Middle button.

If the devices are not part of the same kit, or the units has been purchased separate-

ly, you need to rst pair it in order to use it.

To pair the BTNext to another BTNext unit

To pair the BTNext to another BTNext unit, you must rst enter the setup mode:

1. Turn o the unit

2. Press and hold down the middle button about 7 sec., until the Red light is on

permanently.

3. Now press the Middle button for 3 seconds. The Blue and Red light will ash.

4. Do the same procedure on the other unit, When successfully paired, each unit

will have the Blue light on for one second and then go back to the setup mode

(Red light always on).

5. Now the pairing procedure is complete, you just need to exit the setup mode

before you can use the units:

6. Double click on the Middle button, the Red light will turn o and the Blue light

will start ashing.

You can now use your BTNext.

Attention: remember to switch o all the other Bluetooth device, only the two devices

involved in the pairing must be turned on.

How to use the Intercom with two units

To use the intercom feature, be sure the both units are turned on and correctly paired

together.

Attention: For intercom communication between Driver and Passenger, there is no

need to keep the ip up antenna in the up position. For Bike-to-Bike intercom the an-

tenna must be in the upper position.

Manual activation

Press the Middle button on one of the two units. Communication is enabled and

remains active until you press again the middle button. The intercom need some

second to activate, you will hear a beep tone when the intercom is open.

Voice activation (VOX)

Simply start talking, after some seconds the communication will be opened and will

remain active for the time you are talking. If there is no conversation the intercom

will be closed after 40 seconds. If needed you can close the intercom manually with-

out waiting 40 seconds (just press the middle button).

If needed, you can disable the VOX feature simply by pressing the Backward button

for 7 sec. A voice announcement will advise you when the VOX is disabled. To turn the

VOX on again, just press the same button and a voice announcement will advise you

that the VOX is now active. This setting is remembered also in you turn o the unit.

Attention: The Voice activation (VOX) can open the intercom communication only to

the unit that was paired with the Middle button. If you chose to use a dierent button

(Rear or ), you will be able to active the intercom only manually.

Adjusting the volume

Your Midland BTNext uses AGC technology, which automatically adjusts the listen-

ing volume in relation to background noises.

However, it is also possible to manually adjust the volume by means of the “Volume

+” and “Volume -“buttons.

Attention: volume can be adjust only when an audio connection is active.

How to pair the BTNext to more than two units

One BTNext unit can be paired to maximum ve other BT unit, that mean six in total

(3 Midland unit + 2 Talk2All).

The BTNext has three main buttons (Forward, Middle and Rear). It is up to you which

button use to pair and activate the intercom, you are totally free to choose the but-

ton you like more. The same button you will use to pair the unit will be also used to

activate the intercom communication.

Remember that each device can always be paired with other 3 units at your choice;

as shown in the picture here below, also ‘crossed’ pairing can be done.

For example you can decide to pair one motorbike rider unit to the Forward button,

your passenger to the Middle button and another rider to the Rear button.

In this way you can have in total 5 units paired together and talk to each person,

one by one, simply by pressing the corresponding button (the same used for the

pairing). Every time you open the intercom connection to one person, the previous

connection will be closed.

Rider1

Rider2 Rider3

Passenger1

1 2 3 4 5 6 7 8 9 10 11 ... 15 16

Comments to this Manuals

No comments

Midland BT NEXT User Manual Page 6

Comments to this Manuals

Related products and manuals for Communication Midland BT NEXT