Midland XTC400 Specifications download pdf (Page 10)

Midland XTC400 - 16

Midland XTC400 - 17

Reformatting the Micro SD card

Note: Before the ﬁrst usage Format the microSD card fol-

lowing this procedure

The micro SD card can be reformatted while in the came-

ra. This allows you to completely delete all the les at one

time. Follow these steps:

1. Press and hold the format button

2. Move the RECORD switch to the forward/ON position.

3. The camera will beep 4 times and the icon will alternate

blinking red and blue

When complete, the camera will beep twice, then turn o.

Rotating Lens

To maintain upright orientation for your video when the

camera is mounted at an angle, the XTC400’s lens can ro-

tate 180° in one direction and -90° in the other. There are

indentations every 90° to enable you to twist the lens into

place at commonly used angles.

External Microphone

To connect your camera to an external microphone, rst open

the rubber cover and then insert the 3.5mm microphone jack

into the plug. If you are using a headset, the left speaker will

be used as the microphone. In addition, you may also connect

an mp3 player to directly record music to your video.

HDMI

Connect your micro HDMI cable (not included) to both de-

vices –camera and tv/monitor. Once connected, switch the

camera to the ON (forward) position. This will enable live

streaming, but will not record.

When the switch is moved back to the OFF position, video

playback will start from the micro SD card. To skip to the

next le, toggle the switch ON. For the next le, toggle the

switch OFF. Continue in this manner to ip through your

les. You can always skip forward to the following le, but

cannot move backward to previous les. If you would like to

return to a previous le, you must either unplug the device

from the HDMI cable and plug it in again, or loop through

all of your les.

Battery

The included lithium-ion battery comes partially charged.

To charge, connect the included micro USB cable to camera

and connect the other end of the cable to a power source

such as a computer, wall charger or vehicle charger. No da-

mage will occur to the camera or battery if used prior to a

full charge. See page 20 for battery status indications.

Mounting and Aiming Your Camera

Mount on Dual Track System

The XTC400 was designed with an innovative 3 point

mount system on both sides and the bottom of the camera.

This allows you to mount it on any side with ease.

To mount the camera on the basic mount, slide the camera

onto the track system with the notches on the mount fa-

cing toward the back of the camera.

To detach the camera from the mount, squeeze the mount

release tabs and slide the camera forward.

Aiming the Camera when mounted with the dual track

mount:

When mounting the camera on a helmet, you must do the

following:

1. Consider what you would like to shoot and mount the

camera accordingly- left side, right side or top.

2. Find an appropriate surface and ensure the area is clean

of dirt and debris.Remove the cover of the adhesive pad

and adhere to the helmet.

3. Once attached, adjust the camera to be sure you are l-

ming in the intended direction

4. If needed, rotate the lens to maintain an upright viewing

angle

5. To see where your camera is aimed, enable Wi-Fi and use

your smartphone with the app as a viewnder.

Mounting and Aiming Your Camera

Mount using the Thread Mount

On the bottom of the XTC400 is a standard thread mount

that allows the camera to be mounted to a tripod or other

xture with a 1/4-20 (1/4” diameter, 20 threads per inch)

5/16 deep thread. To attach the camera, insert the screw on

the mount into the camera thread and rotate the camera

clockwise to tighten down onto the screw.

Note: Over tightening may cause damage to the mount and/

or camera

Tripod Mount

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 59 60

Comments to this Manuals

No comments

Midland XTC400 Specifications Page 10

Comments to this Manuals